Kyropoulos method can be shorted as KY method. This method is the first
to propose to grow crystals in 1926.later on, it is widely used in the
production and research of large-size crystal halogen, hydroxide and
carbonate crystals. In 1960s and 1970s, it is improved by former Soviet
Union Musatov for the production of sapphire crystals.
The single crystal grown by Kyropoulos method is always shaped like a
pear. Its crystal diameter crucible can grow to less than the inner
diameter of the small size of 10 ~ 30mm. The principle is similar to
Czochralski method. Firstly, heating raw material to the melting point
molten metal melt, then a single crystal of the seed (Seed Crystal,
also known as seed rod) to contact the molten metal surface, began to
grow on the seed crystal and solid-liquid interface and the molten metal
single crystal of the same crystal structure seed, seed to a very slow
speed pulled up. After then, the seed crystal will be pull up to a
height and form a crystal neck, the molten metal solidification rates
and stable interface seed, the seed will not pulling up, but nor make
the rotation. But only the controlling of the cooling rate of the
single crystal is gradually solidified from the top down, and finally
solidified into a whole monocrystalline.
This method is applied tungsten crucible as vapor to grow sapphire.
If there is any other question refer to tungsten crucible for sapphire
growth furnace, please feel free to contact us through the following
methods:
Email:sales@chinatungsten.com
Tel.:+86 592 512 9696
Fax:+86 592 512 9797
2015年12月28日星期一
Sapphire (Growing in Tungsten Crucible) for Laser Host
Sapphire crystal, growing in tungsten crucible, is an excellent laser host materials, such as
titanium-doped sapphire crystal is the world's most outstanding
broadband tunable laser crystal today, its tunable wavelength range of
660 ~ 1200nm. Moulton was first reported since 1982 to achieve laser
oscillation since, because of its very wide tuning range and high gain,
etc., which have been widely and well studied. With sapphire optical
penetration range is very wide, from near-ultraviolet to mid-infrared
light wavelength 0.9nm wavelength 5.5μm have good light transmittance,
and within the band of 0.25 ~ 4.5μm is still more than 80% penetration
rate; making large size, high integrity sapphire single crystal has
been used as the matrix material US LICO (Laser interferometer
gravitational observatory) project and other large interferometric
device for measuring cosmic gravity waves in the preferred spectral
components. Sapphire crystal used in civilian areas has also been very
widely, such as in medical equipment, environmental equipment, laser
equipment, chemical equipment, high vacuum test equipment, fiber guide
wire plate textile industry, bar code scanners to scan window, never
wear type Rado watch Mongolia and the like.
If there is any other question refer to molybdenum
heating element for sapphire growth furnace, please feel free to contact
us through the following methods.
2015年12月25日星期五
Main Features for SAPMAC Methods-Sapphire and Tungsten
Main features for SAPMAC Methods, which is sapphire growth method and used tungsten as vector:
1) Put through a cold heart shoulder, to ensure that the large size of the crystal growth process of the crystal to the entire end product of genetic characteristics of a good, good material quality.
2) Through high-precision energy control with micro-pulling, so that no significant thermal disturbance in the whole process of crystal growth, significantly reduced the probability of defect initiation than other methods.
3) Since only trace pulling, reducing the temperature field perturbation. Make more uniform temperature field, so as to ensure the success rate of single crystal growth.
4) Throughout the crystal growth process, the crystal is not made crucible, it is still in the hot zone. It can precisely control the cooling rate, to reduce the thermal stress.
5) Suitable for the growth of large-size crystals, the material is more than 1.2 times the comprehensive utilization Kyropoulos law.
6) Use water as the working fluid within the heat exchanger, the crystal can be achieved in-situ annealing, short test cycle than other methods, and low cost.
7) In the crystal growth process, we can easily observe the growth of crystals.
8) Free surface crystal growth, the crucible is not mandatory, can reduce stress Crystals.
9) Can easily use the desired orientation seed and "necking" process, it helps to relatively fast rate.
If there is any other question refer to tungsten crucible for sapphire growth furnace, please feel free to contact us through the following methods:
Email:sales@chinatungsten.com
Tel.:+86 592 512 9696
Fax:+86 592 512 9797
1) Put through a cold heart shoulder, to ensure that the large size of the crystal growth process of the crystal to the entire end product of genetic characteristics of a good, good material quality.
2) Through high-precision energy control with micro-pulling, so that no significant thermal disturbance in the whole process of crystal growth, significantly reduced the probability of defect initiation than other methods.
3) Since only trace pulling, reducing the temperature field perturbation. Make more uniform temperature field, so as to ensure the success rate of single crystal growth.
4) Throughout the crystal growth process, the crystal is not made crucible, it is still in the hot zone. It can precisely control the cooling rate, to reduce the thermal stress.
5) Suitable for the growth of large-size crystals, the material is more than 1.2 times the comprehensive utilization Kyropoulos law.
6) Use water as the working fluid within the heat exchanger, the crystal can be achieved in-situ annealing, short test cycle than other methods, and low cost.
7) In the crystal growth process, we can easily observe the growth of crystals.
8) Free surface crystal growth, the crucible is not mandatory, can reduce stress Crystals.
9) Can easily use the desired orientation seed and "necking" process, it helps to relatively fast rate.
If there is any other question refer to tungsten crucible for sapphire growth furnace, please feel free to contact us through the following methods:
Email:sales@chinatungsten.com
Tel.:+86 592 512 9696
Fax:+86 592 512 9797
Sapphire Grow Method- Micro-Pulling And Shoulder Expanding at Cooled Center (SAPMAC)
Micro-pulling and shoulder expanding at cooled center is a sapphire
growth method, which is also called micro-pulling rotation Kyropoulos.
The is an improved method based on Kyropoulos Method and Pulling Method
by Institute of Composite Structures from the Harbin Institute of
Technology. It is used to grow large size crystal. Crystal growing
system includes control system, vacuum system, heating body, cooling
system and thermal protection systems. The following a picture, which is
a schematic shoulder cold heart to put the system trace Czochralski
method, SAPMAC grown single crystal, the outlook is usually pear-shaped,
crystal diameter crucible can grow to more than the inner diameter of
the small size of 10 ~ 30mm. The seed is processed into split shape, use
seed clips at the bottom of the heat exchanger. Rotating and pulling
the heat exchanger can be accomplished seed fixed, crystals, and the
exchange interaction between the heat exchanger, crystal and melt.
Tungsten crucible is widely used in sapphire growth furnace, including SAPMAC method.
If there is any other question refer to tungsten crucible for sapphire growth furnace, please feel free to contact us through the following methods:
Email:sales@chinatungsten.com
Tel.:+86 592 512 9696
Fax:+86 592 512 9797
Tungsten crucible is widely used in sapphire growth furnace, including SAPMAC method.
If there is any other question refer to tungsten crucible for sapphire growth furnace, please feel free to contact us through the following methods:
Email:sales@chinatungsten.com
Tel.:+86 592 512 9696
Fax:+86 592 512 9797
订阅:
博文 (Atom)